Urgent.News

What's breaking now, across thousands of outlets.

Tech

How Does Co-Channel Interference Occur in Wireless Communication? Causes, Troubleshooting and Mitigation

The answer: Co-channel interference occurs when two or more devices transmitting on the same frequency and channel overlap in the air: the receiving antenna picks up the vector superposition of all their energy, and once the interference approaches or exceeds the desired signal, the receiver's demodulation threshold rises and the bit error rate soars. Its three common sources are other legitimate…

Co-channel interference in wireless communication occurs when two or more devices transmit on the same frequency and channel, resulting in the receiving antenna capturing the combined energy of all transmitters. This leads to a rise in the receiver's demodulation threshold and an increase in bit error rate. Three common sources of this interference are other legitimate users in the same license-free band, improper self-networking planning, and electromagnetic leakage from equipment itself.

To diagnose co-channel interference, engineers can isolate the RF link, monitor noise-floor statistics and time patterns, and implement solutions such as frequency planning, spread-spectrum modulation, lower air rates, proper antenna placement, and protocol-layer retransmission. In most cases, the interference is caused by other devices operating on the same frequency and channel.

Radio waves do not recognize their owner, so when multiple devices transmit simultaneously on the same frequency, the receiver picks up the vector superposition of all signals. This interference becomes problematic when its strength matches or exceeds the desired signal, causing a higher demodulation threshold and a higher error rate. There are three common sources of interference: other legitimate users within the band, improper self-networking planning, and electromagnetic leakage from equipment.

Troubleshooting co-channel interference involves proving that the problem lies in the air interface and identifying the source of the interference. Engineers can isolate the link factors by separating the two modules with a shielded box or testing them far apart. If communication becomes stable after shielding, the air-interface interference can be confirmed. Otherwise, engineers should check the antenna, power supply, and UART wiring before attributing the issue to interference.

Common mitigation methods include frequency planning, using spread-spectrum modulations with better interference resistance, opting for lower air rates, proper antenna placement, and implementing protocol-layer retransmission. Frequency planning involves staggering channels and using module network IDs and communication keys for logical isolation.

Spread-spectrum modulations, like ChirpIoT and LoRa, have a better demodulation sensitivity than traditional narrowband FSK, allowing for better handling of interference. Lowering air rates can improve receiver sensitivity and link margin, while proper antenna placement helps avoid interference from nearby devices. Protocol-layer retransmission enables ACK and packet-segment verification, while a master-slave architecture can help schedule transmit/receive timing uniformly to avoid simultaneous transmissions.

Written by urgent.news from Dev.to's reporting — not their text. Machine-written — may contain errors; check the original before relying on it.

Read the original at dev.to →

More in Tech

Stop asking one prompt to do three jobs

Adapted from the first lesson of Designing Multi-Agent Systems on Learnvoro. Originally published on Medium . Most AI workflows start as one long prompt: read this document, decide what matters, write…

Will Your Photo Come Out Sideways? A Python EXIF Orientation Preflight Before You Pay for a Bama Bound Clip (Tested)

Checked November 17, 2026 (15:19–15:21 CST, UTC+8). I build bamabound.app , an independent studio that turns one photo of one person into a vertical clip of them holding a red I'M BAMA BOUND banner.

  • Studio bamabound.app creates vertical clips of people holding a "I M BAMA BOUND" banner
  • JPEG, PNG, or WebP formats accepted, max 10 MB, must display person's face
  • EXIF Orientation tag can cause photos to appear sideways if not adjusted

Before You Batch-Convert a Folder of Videos, Test One File from Each Source

Suppose your project folder contains phone clips, camera footage, and a screen recording. You want them all to work in one editor or upload destination.

  • Test one file from each source type before batch conversion
  • Check destination requirements for file formats, codecs, dimensions
  • Verify pilot file meets requirements before processing entire group

More from Tuesday 17 November →